| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is entirely SoC clk drivers.
The majority diff wise is for the new Rockchip and Qualcomm clk
drivers which is mostly lines and lines of data structures to describe
the clk hardware in these SoCs. Beyond those two, Renesas continues to
incrementally add clks to their SoC drivers, causing them to show up
higher in the diffstat this time because they added quite a few clks
all over the place.
Overall it is a semi-quiet release that has some new clk drivers and
the usual fixes for clock data that was wrong or missing and
non-critical cleanups that plug error paths or fix typos.
New Drivers:
- Qualcomm IPQ5424 Network Subsystem Clock Controller
- Qualcomm SM8750 Video Clock Controller
- Rockchip RV1126B and RK3506 clock drivers
- i.MX8ULP SIM LPAV clock driver
- Samsung ACPM (firmware interface) clock driver
- Altera Agilex5 clock driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (117 commits)
clk: keystone: fix compile testing
clk: keystone: syscon-clk: fix regmap leak on probe failure
clk: qcom: Mark camcc_sm7150_hws static
clk: samsung: exynos-clkout: Assign .num before accessing .hws
clk: rockchip: Add clock and reset driver for RK3506
dt-bindings: clock: rockchip: Add RK3506 clock and reset unit
clk: actions: Fix discarding const qualifier by 'container_of' macro
clk: spacemit: Set clk_hw_onecell_data::num before using flex array
clk: visconti: Add VIIF clocks
dt-bindings: clock: tmpv770x: Add VIIF clocks
dt-bindings: clock: tmpv770x: Remove definition of number of clocks
clk: visconti: Do not define number of clocks in bindings
clk: rockchip: Add clock controller for the RV1126B
dt-bindings: clock, reset: Add support for rv1126b
clk: rockchip: Implement rockchip_clk_register_armclk_multi_pll()
clk: qcom: x1e80100-dispcc: Add USB4 router link resets
dt-bindings: clock: qcom: x1e80100-dispcc: Add USB4 router link resets
clk: qcom: videocc-sm8750: Add video clock controller driver for SM8750
dt-bindings: clock: qcom: Add SM8750 video clock controller
clk: qcom: branch: Extend invert logic for branch2 mem clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"This is the first half of the driver changes:
- A treewide interface change to the "syscore" operations for power
management, as a preparation for future Tegra specific changes
- Reset controller updates with added drivers for LAN969x, eic770 and
RZ/G3S SoCs
- Protection of system controller registers on Renesas and Google
SoCs, to prevent trivially triggering a system crash from e.g.
debugfs access
- soc_device identification updates on Nvidia, Exynos and Mediatek
- debugfs support in the ST STM32 firewall driver
- Minor updates for SoC drivers on AMD/Xilinx, Renesas, Allwinner, TI
- Cleanups for memory controller support on Nvidia and Renesas"
* tag 'soc-drivers-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (114 commits)
memory: tegra186-emc: Fix missing put_bpmp
Documentation: reset: Remove reset_controller_add_lookup()
reset: fix BIT macro reference
reset: rzg2l-usbphy-ctrl: Fix a NULL vs IS_ERR() bug in probe
reset: th1520: Support reset controllers in more subsystems
reset: th1520: Prepare for supporting multiple controllers
dt-bindings: reset: thead,th1520-reset: Add controllers for more subsys
dt-bindings: reset: thead,th1520-reset: Remove non-VO-subsystem resets
reset: remove legacy reset lookup code
clk: davinci: psc: drop unused reset lookup
reset: rzg2l-usbphy-ctrl: Add support for RZ/G3S SoC
reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G3S support
reset: eswin: Add eic7700 reset driver
dt-bindings: reset: eswin: Documentation for eic7700 SoC
reset: sparx5: add LAN969x support
dt-bindings: reset: microchip: Add LAN969x support
soc: rockchip: grf: Add select correct PWM implementation on RK3368
soc/tegra: pmc: Add USB wake events for Tegra234
amba: tegra-ahb: Fix device leak on SMMU enable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver, lots of various updates to existing ones, some
refactoring support for new models and misc tweaks and fixes.
The biggest new feature in GPIO core is adding support for managed,
enable-counted sharing of GPIO pins, something that - until now - was
only hacked around with the GPIOD_FLAGS_BIT_NONEXCLUSIVE request flag
which basically allowed drivers to "fight it out" for the descriptor
and provided no synchronization. It was enabled on Qualcomm platforms
(and thus is enabled on arm64 defconfig) and I plan on removing
GPIOD_FLAGS_BIT_NONEXCLUSIVE once all drivers using it are switched to
the new mechanism.
GPIO core:
- add proper support for shared GPIOs that's aiming to replace the
current sharing mechanism (which provides no synchronization ot
enable counting) and enable it for Qualcomm platforms
- improve the software node GPIO lookup by using the fwnode
representation instead of the software node's name which was prone
to bugs (GPIO controllers don't have to use the software node's
name as their kernel label)
- remove the last user of legacy-of-mm-gpiochip.h and drop the header
- move closer to removing the legacy gpio_request_one() routine
- rename some symbols for consistency
- shrink GPIO printk() helpers by reusing existing code
- remove some redundant kernel messages
- use min() instead of min_t() in GPIO ACPI code
- use system_percpu_wq instead of system_wq in GPIO character device
code
New drivers:
- add a driver for the QIXIS FPGA GPIO controller
Driver improvements:
- use modernized variants of power management macros across a wide
array of drivers in order to avoid having to use the __maybe_unused
attribute
- convert gpio-elkhartlake and reset-gpio to using the auxiliary bus
instead of the platform bus as they are not really described in
firmware
- use lock guards and update symbol prefixes in gpio-mmio
- support the bryx radio interface kit in gpio-mpsse + refactor the
driver
- use software nodes for configuring the reset-gpio driver, including
setting up the reference to the shared "reset" pin
- check and propagate the return value of gpiod_set_value() to
user-space in gpio-virtuser (this was previously not possible as
this function returned void)
- extend the gpio-regmap helper with more features (bypass cache for
aliased inputs, force writes for aliased data registers, add a new
configuration parameter)
- remove unneeded includes from gpio-aspeed and gpio-latch
- add support for Tegra410 to gpio-tegra186
- replace PCI-specific PM with generic device-level PM in gpio-bt8xx
- use dynamic GPIO range allocation in gpio-loongson-64bit
- improve handling of level-triggered interrupts in gpio-pca953x
- add suspend/resume support to gpio-fxl6408
- add support for more models to gpio-menz127
- optimize gpio-mvebu interrupt handling by avoiding unnecessary
calls to mvebu_gpio_irq_handler()
- make locking more consistent in gpio-grgpio
Device-tree bindings:
- document new NXP and Microchip models
Documentation:
- add a comprehensive compatibility and feature list for
gpio-pca953x, which is a great addition as it's probably the most
commonly used GPIO expander driver
- kernel-doc tweaks
Late fixes:
- use BYTE_CTRL_MODE for 2K2000/3000 models in gpio-loongson"
* tag 'gpio-updates-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (80 commits)
gpio: loongson: Switch 2K2000/3000 GPIO to BYTE_CTRL_MODE
gpio: regmap: fix kernel-doc notation
gpio: shared: fix a deadlock
gpio: shared-proxy: set suppress_bind_attrs
gpio: shared: ignore GPIO hogs when traversing the device tree
gpio: shared: ignore special __symbols__ node when traversing device tree
gpio: shared: handle the reset-gpios corner case
gpio: zynq: Use modern PM macros
gpio: xilinx: Use modern PM macros
gpio: xgene: Use modern PM macros
gpio: uniphier: Use modern PM macros
gpio: tqmx86: Use modern PM macros
gpio: pch: Use modern PM macros
gpio: omap: Use modern PM macros
gpio: msc313: Use modern PM macros
gpio: mlxbf2: Use modern PM macros
gpio: ml-ioh: Use modern PM macros
gpio: pl061: Use modern PM macros
gpio: htc-egpio: Use modern PM macros
gpio: brcmstb: Use modern PM macros
...
|
|
GPIO machine lookup is a nice mechanism for associating GPIOs with
consumers if we don't know what kind of device the GPIO provider is or
when it will become available. However in the case of the reset-gpio, we
are already holding a reference to the device and so can reference its
firmware node. Let's setup a software node that references the relevant
GPIO and attach it to the auxiliary device we're creating.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
As the reset-gpio devices are purely virtual and never instantiated from
real firmware nodes, let's convert the driver to using the - more
fitting - auxiliary bus.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Auxiliary devices really do need a parent so ahead of converting the
reset-gpios driver to registering on the auxiliary bus, make the GPIO
device that provides the reset GPIO the parent of the reset-gpio device.
To that end move the lookup of the GPIO device by fwnode to the
beginning of __reset_add_reset_gpio_device() which has the added benefit
of bailing out earlier, before allocating resources for the virtual
device, if the chip is not up yet.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
For better readability and easier maintenance order the includes
alphabetically.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The devm_regmap_field_alloc() function never returns NULL, it returns
error pointers. Update the error checking to match.
Fixes: 58128aa88867 ("reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Introduce reset controllers for AP, MISC, VI, VP and DSP subsystems and
add their reset signal mappings.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
TH1520 SoC is divided into several subsystems, shipping distinct reset
controllers with similar control logic. Let's make reset signal mapping
a data structure specific to one compatible to prepare for introduction
of more reset controllers in the future.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
There are no more users of this code. Let's remove the exported symbols
and the implementation from reset core.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[p.zabel@pengutronix.de: folded in 8e6ec20e-8965-4b42-99fc-0462269ff2f1@paulmck-laptop]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The Renesas RZ/G3S SoC USB PHY HW block receives as input the USB PWRRDY
signal from the system controller. Add support for the Renesas RZ/G3S SoC.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
On the Renesas RZ/G3S SoC, the USB PHY block has an input signal called
PWRRDY. This signal is managed by the system controller and must be
de-asserted after powering on the area where USB PHY resides and asserted
before powering it off.
On power-on/resume the USB PWRRDY signal need to be de-asserted before
enabling clock and switching the module to normal state (through MSTOP
support). The power-on/resume configuration sequence must be:
1/ PWRRDY=0
2/ CLK_ON=1
3/ MSTOP=0
On power-off/suspend the configuration sequence should be:
1/ MSTOP=1
2/ CLK_ON=0
3/ PWRRDY=1
The CLK_ON and MSTOP functionalities are controlled by clock drivers.
The suspend/resume support will be handled by different patches.
After long discussions with the internal HW team, it has been confirmed
that the HW connection b/w USB PHY block, the USB channels, the system
controller, clock, MSTOP, PWRRDY signal is as follows:
┌──────────────────────────────┐
│ │◄── CPG_CLKON_USB.CLK0_ON
│ USB CH0 │
┌──────────────────────────┐ │┌───────────────────────────┐ │◄── CPG_CLKON_USB.CLK2_ON
│ ┌────────┐ ││host controller registers │ │
│ │ │ ││function controller registers│
│ │ PHY0 │◄──┤└───────────────────────────┘ │
│ USB PHY │ │ └────────────▲─────────────────┘
│ └────────┘ │
│ │ CPG_BUS_PERI_COM_MSTOP.MSTOP{6, 5}_ON
│┌──────────────┐ ┌────────┐
││USHPHY control│ │ │
││ registers │ │ PHY1 │ ┌──────────────────────────────┐
│└──────────────┘ │ │◄──┤ USB CH1 │
│ └────────┘ │┌───────────────────────────┐ │◄── CPG_CLKON_USB.CLK1_ON
└─▲───────▲─────────▲──────┘ ││ host controller registers │ │
│ │ │ │└───────────────────────────┘ │
│ │ │ └────────────▲─────────────────┘
│ │ │ │
│ │ │ CPG_BUS_PERI_COM_MSTOP.MSTOP7_ON
│PWRRDY │ │
│ │ CPG_CLK_ON_USB.CLK3_ON
│ │
│ CPG_BUS_PERI_COM_MSTOP.MSTOP4_ON
│
┌────┐
│SYSC│
└────┘
where:
- CPG_CLKON_USB.CLK.CLKX_ON is the register bit controlling the clock X
of different USB blocks, X in {0, 1, 2, 3}
- CPG_BUS_PERI_COM_MSTOP.MSTOPX_ON is the register bit controlling the
MSTOP of different USB blocks, X in {4, 5, 6, 7}
- USB PHY is the USB PHY block exposing 2 ports, port0 and port1, used
by the USB CH0, USB CH1
- SYSC is the system controller block controlling the PWRRDY signal
- USB CHx are individual USB block with host and function capabilities
(USB CH0 have both host and function capabilities, USB CH1 has only
host capabilities)
The USBPHY control registers are controlled though the
reset-rzg2l-usbphy-ctrl driver. The USB PHY ports are controlled by
phy_rcar_gen3_usb2 (drivers/phy/renesas/phy-rcar-gen3-usb2.c file). The
USB PHY ports request resets from the reset-rzg2l-usbphy-ctrl driver.
The connection b/w the system controller and the USB PHY CTRL driver is
implemented through the renesas,sysc-pwrrdy device tree property
proposed in this patch. This property specifies the register offset and the
bitmask required to control the PWRRDY signal.
Since the USB PHY CTRL driver needs to be probed before any other
USB-specific driver on RZ/G3S, control of PWRRDY is passed exclusively
to it. This guarantees the correct configuration sequence between clocks,
MSTOP bits, and the PWRRDY bit on probe/resume and remove/suspend. At the
same time, changes are kept minimal by avoiding modifications to the USB
PHY driver to also handle the PWRRDY itself.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for reset controller in eic7700 series chips.
Provide functionality for asserting and deasserting resets
on the chip.
Signed-off-by: Yifeng Huang <huangyifeng@eswincomputing.com>
Signed-off-by: Xuyang Dong <dongxuyang@eswincomputing.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
LAN969x uses the same reset configuration as LAN966x, but we need to
allow compiling it when ARCH_LAN969X is selected.
A fallback compatible to LAN966x will be used.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
While the auxiliary bus was a nice bandaid, and meant that re-writing
the representation of the clock regions in devicetree was not required,
it has run its course. The "mss_top_sysreg" region that contains the
clock and reset regions, also contains pinctrl and an interrupt
controller, so the time has come rewrite the devicetree and probe the
reset controller from an mfd devicetree node, rather than implement
those drivers using the auxiliary bus. Wanting to avoid propagating this
naive/incorrect description of the hardware to the new pic64gx SoC is a
major motivating factor here.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As per the i.MX8MP TRM, section 14.2 "AUDIO_BLK_CTRL", table 14.2.3.1.1
"memory map", the definition of the EARC control register shows that the
EARC controller software reset is controlled via bit 0, while the EARC PHY
software reset is controlled via bit 1.
This means that the current definitions of IMX8MP_AUDIOMIX_EARC_RESET_MASK
and IMX8MP_AUDIOMIX_EARC_PHY_RESET_MASK are wrong since their values would
imply that the EARC controller software reset is controlled via bit 1 and
the EARC PHY software reset is controlled via bit 2. Fix them.
Fixes: a83bc87cd30a ("reset: imx8mp-audiomix: Prepare the code for more reset bits")
Cc: stable@vger.kernel.org
Reviewed-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
|
|
Make sure to drop the OF node reference taken when probing the auxiliary
device when the device is later unbound.
Fixes: 487b1b32e317 ("reset: eyeq: add platform driver")
Cc: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250708085613.15823-1-johan@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
When using MMIO with regmap, fast_io is implied. No need to set it
again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Drew Fustini <fustini@kernel.org> # for reset-th1520.c
Link: https://lore.kernel.org/r/20250813161517.4746-17-wsa+renesas@sang-engineering.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The VO subsystem of TH1520 contains a few resets for the display
pipeline -- display, MIPI DSI and HDMI controllers.
Add support for them to the reset-th1520 driver.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250813081716.2181843-3-uwu@icenowy.me
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The AST2700 reset driver is registered as an auxiliary device
due to reset and clock controller share the same register region.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250708052909.4145983-3-ryan_chen@aspeedtech.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The ephy control register on bcm63xx SoCs contain bits for
resetting individual internal phys. Use the existing bcm6345-reset
driver to set bits.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Link: https://lore.kernel.org/r/20250715234605.36216-2-kylehendrydev@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is the usual collection of primarily clk driver updates.
The big part of the diff is all the new Qualcomm clk drivers added for
a few SoCs they're working on. The other two vendors with significant
work this cycle are Renesas and Amlogic. Renesas adds a bunch of clks
to existing drivers and supports some new SoCs while Amlogic is
starting a significant refactoring to simplify their code.
The core framework gained a pair of helpers to get the 'struct device'
or 'struct device_node' associated with a 'struct clk_hw'. Some
associated KUnit tests were added for these simple helpers as well.
Beyond that core change there are lots of little fixes throughout the
clk drivers for the stuff we see every day, wrong clk driver data that
affects tree topology or supported frequencies, etc. They're not found
until the clks are actually used by some consumer device driver.
New Drivers:
- Global, display, gpu, video, camera, tcsr, and rpmh clock
controller for the Qualcomm Milos SoC
- Camera, display, GPU, and video clock controllers for Qualcomm
QCS615
- Video clock controller driver for Qualcomm SM6350
- Camera clock controller driver for Qualcomm SC8180X
- I3C clocks and resets on Renesas RZ/G3E
- Expanded Serial Peripheral Interface (xSPI) clocks and resets on
Renesas RZ/V2H(P) and RZ/V2N
- SPI (RSPI) clocks and resets on Renesas RZ/V2H(P)
- SDHI and I2C clocks on Renesas RZ/T2H and RZ/N2H
- Ethernet clocks and resets on Renesas RZ/G3E
- Initial support for the Renesas RZ/T2H (R9A09G077) and RZ/N2H
(R9A09G087) SoCs
- Ethernet clocks and resets on Renesas RZ/V2H and RZ/V2N
- Timer, I2C, watchdog, GPU, and USB2.0 clocks and resets on Renesas
RZ/V2N
Updates:
- Support atomic PWMs in the PWM clk driver
- clk_hw_get_dev() and clk_hw_get_of_node() helpers
- Replace round_rate() with determine_rate() in various clk drivers
- Convert clk DT bindings to DT schema format for DT validation
- Various clk driver cleanups and refactorings from static analysis
tools and possibly real humans
- A lot of little fixes here and there to things like clk tree
topology, missing frequencies, flagging clks as critical, etc"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (216 commits)
clk: clocking-wizard: Fix the round rate handling for versal
clk: Fix typos
clk: spacemit: ccu_pll: fix error return value in recalc_rate callback
clk: tegra: periph: Make tegra_clk_periph_ops static
clk: tegra: periph: Fix error handling and resolve unsigned compare warning
clk: imx: scu: convert from round_rate() to determine_rate()
clk: imx: pllv4: convert from round_rate() to determine_rate()
clk: imx: pllv3: convert from round_rate() to determine_rate()
clk: imx: pllv2: convert from round_rate() to determine_rate()
clk: imx: pll14xx: convert from round_rate() to determine_rate()
clk: imx: pfd: convert from round_rate() to determine_rate()
clk: imx: frac-pll: convert from round_rate() to determine_rate()
clk: imx: fracn-gppll: convert from round_rate() to determine_rate()
clk: imx: fixup-div: convert from round_rate() to determine_rate()
clk: imx: cpu: convert from round_rate() to determine_rate()
clk: imx: busy: convert from round_rate() to determine_rate()
clk: imx: composite-93: remove round_rate() in favor of determine_rate()
clk: imx: composite-8m: remove round_rate() in favor of determine_rate()
clk: qcom: Remove redundant pm_runtime_mark_last_busy() calls
clk: imx: Remove redundant pm_runtime_mark_last_busy() calls
...
|
|
Implement reset support for SpacemiT CCUs. A SpacemiT reset controller
device is an auxiliary device associated with a clock controller (CCU).
This patch defines the reset controllers for the MPMU, APBC, and MPMU
CCUs, which already define clock controllers. It also adds RCPU, RCPU2,
and ACPB2 CCUs, which only define resets.
Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250702113709.291748-6-elder@riscstar.com
Signed-off-by: Yixun Lan <dlan@gentoo.org>
|
|
The BRCMSTB and BRCMSTB_RESCAL reset drivers are also
used in the BCM2712, AKA the RPi5. The RPi platforms
have typically used the ARCH_BCM2835, and the PCIe
support for this SoC can use this config which depends
on these drivers so enable building them when just that
arch option is enabled to ensure the platform works as
expected.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250630175301.846082-1-pbrobinson@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Reuse reset-simple driver for the Sophgo CV1800B reset generator.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250617070144.1149926-3-inochiama@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The auxiliary device creation of this driver is simple enough to
use the available auxiliary device creation helper.
Use it and remove some boilerplate code.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20250611-rst-mpfs-aux-v1-1-c86534b473c3@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Fix trivial typo in the Kconfig entry for RESET_TH1520.
Fixes: 4a65326311ab ("reset: thead: Add TH1520 reset controller driver")
Signed-off-by: Drew Fustini <drew@pdp7.com>
Link: https://lore.kernel.org/r/20250601181000.166088-1-drew@pdp7.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for the resets on Canaan Kendryte K230 SoC. The driver
support CPU0, CPU1, L2 cache flush, hardware auto clear and software
clear resets.
Tested-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Link: https://lore.kernel.org/r/20250613-k230-reset-v4-2-e5266d2be440@pigmoral.tech
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Implement a USB2PHY port reset driver for the Renesas RZ/V2H(P) SoC.
Enable control of USB2.0 PHY reset and power-down operations, including
assert and deassert functionalities for the PHY.
Leverage device tree (OF) data to support future SoCs with similar USB2PHY
hardware but varying register configurations. Define initialization values
and control register settings to ensure flexibility for upcoming platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20250415195131.281060-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add reset controller driver for the T-HEAD TH1520 SoC that manages
hardware reset lines for various subsystems. The driver currently
implements support for GPU reset control, with infrastructure in place
to extend support for NPU and Watchdog Timer resets in future updates.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Link: https://lore.kernel.org/r/20250303152511.494405-3-m.wilczynski@samsung.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
- Transition the i.MX8MP DSP remoteproc driver to use the reset
framework for driving the run/stall reset bits
- Add support for managing the modem remoteprocessor on the Qualcomm
MSM8226, MSM8926, and SM8750 platforms
* tag 'rproc-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: qcom_q6v5_pas: Make single-PD handling more robust
remoteproc: qcom_q6v5_pas: Use resource with CX PD for MSM8226
remoteproc: core: Clear table_sz when rproc_shutdown
remoteproc: sysmon: Update qcom_add_sysmon_subdev() comment
dt-bindings: remoteproc: Consolidate SC8180X and SM8150 PAS files
irqdomain: remoteproc: Switch to of_fwnode_handle()
remoteproc: qcom: pas: add minidump_id to SC7280 WPSS
remoteproc: imx_dsp_rproc: Document run_stall struct member
remoteproc: qcom: pas: Add SM8750 MPSS
dt-bindings: remoteproc: Add SM8750 MPSS
imx_dsp_rproc: Use reset controller API to control the DSP
reset: imx8mp-audiomix: Add support for DSP run/stall
reset: imx8mp-audiomix: Introduce active_low configuration option
reset: imx8mp-audiomix: Prepare the code for more reset bits
reset: imx8mp-audiomix: Add prefix for internal macro
dt-bindings: dsp: fsl,dsp: Add resets property
dt-bindings: reset: audiomix: Add reset ids for EARC and DSP
remoteproc: qcom_wcnss: Handle platforms with only single power domain
dt-bindings: remoteproc: qcom,wcnss-pil: Add support for single power-domain platforms
remoteproc: qcom_q6v5_mss: Add modem support on MSM8926
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"These are the updates for SoC specific drivers and related subsystems:
- Firmware driver updates for SCMI, FF-A and SMCCC firmware
interfaces, adding support for additional firmware features
including SoC identification and FF-A SRI callbacks as well as
various bugfixes
- Memory controller updates for Nvidia and Mediatek
- Reset controller support for microchip sam9x7 and imx8qxp/imx8qm
- New hardware support for multiple Mediatek, Renesas and Samsung
Exynos chips
- Minor updates on Zynq, Qualcomm, Amlogic, TI, Samsung, Nvidia and
Apple chips
There will be a follow up with a few more driver updates that are
still causing build regressions at the moment"
* tag 'soc-drivers-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (97 commits)
irqchip: Add support for Amlogic A4 and A5 SoCs
dt-bindings: interrupt-controller: Add support for Amlogic A4 and A5 SoCs
reset: imx: fix incorrect module device table
dt-bindings: power: qcom,kpss-acc-v2: add qcom,msm8916-acc compatible
bus: qcom-ssc-block-bus: Fix the error handling path of qcom_ssc_block_bus_probe()
bus: qcom-ssc-block-bus: Remove some duplicated iounmap() calls
soc: qcom: pd-mapper: Add support for SDM630/636
reset: imx: Add SCU reset driver for i.MX8QXP and i.MX8QM
dt-bindings: firmware: imx: add property reset-controller
dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7
memory: mtk-smi: Add ostd setting for mt8192
dt-bindings: soc: samsung: exynos-usi: Drop unnecessary status from example
firmware: tegra: bpmp: Fix typo in bpmp-abi.h
soc/tegra: pmc: Use str_enable_disable-like helpers
soc: samsung: include linux/array_size.h where needed
firmware: arm_scmi: use ioread64() instead of ioread64_hi_lo()
soc: mediatek: mtk-socinfo: Add extra entry for MT8395AV/ZA Genio 1200
soc: mediatek: mt8188-mmsys: Add support for DSC on VDO0
soc: mediatek: mmsys: Migrate all tables to MMSYS_ROUTE() macro
soc: mediatek: mt8365-mmsys: Fix routing table masks and values
...
|
|
The ID table is for of_device_id, not platform_device_id:
ERROR: modpost: drivers/reset/reset-imx-scu: type mismatch between imx_scu_reset_ids[] and MODULE_DEVICE_TABLE(platform, ...)
Fixes: 6b64fde5c183 ("reset: imx: Add SCU reset driver for i.MX8QXP and i.MX8QM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250314153541.3555813-1-arnd@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
We can Run/Stall the DSP via audio block control bits found in audiomix.
Implement this functionality using the reset controller and use assert
for Stall and deassert for Run.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250311085812.1296243-8-daniel.baluta@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
For EARC and EARC PHY the reset happens when clearing the reset bits.
Refactor assert/deassert function in order to take into account the
active_low configuration option.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20250311085812.1296243-7-daniel.baluta@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Current code supports EARC PHY Software Reset and EARC Software Reset
but it is not easily extensible to more reset bits.
So, refactor the code in order to easily allow more reset bits in the
future.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250311085812.1296243-6-daniel.baluta@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
This adds IMX8MP_AUDIOMIX_ prefix to internal macros in order to show
that specific macros are related to audiomix.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20250311085812.1296243-5-daniel.baluta@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
With the blamed commit it seems that lan966x doesn't seem to boot
anymore when the internal CPU is used.
The reason seems to be the usage of the devm_of_iomap, if we replace
this with devm_ioremap, this seems to fix the issue as we use the same
region also for other devices.
Fixes: 0426a920d6269c ("reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x")
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Tested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250227105502.25125-1-horatiu.vultur@microchip.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add System Controller Firmware(SCU) reset driver for i.MX8QM and i.MX8QXP.
SCU Manage resets for peripherals such as MIPI CSI. Currently, support two
reset sources: IMX_SC_R_CSI_0 and IMX_SC_R_CSI_1.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250210-8qxp_camera-v3-2-324f5105accc@nxp.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"These are changes to SoC specific drivers and DT bindings that don't
have a separate subsystem tree, or that get grouped here for
simplicity.
Nothing out of the ordinary for the 6.14 release here:
- Most of the updates are for Qualcomm specific drivers, adding
support for additional SoCs in the exssting drivers, and support
for wrapped encryption key access in the SCM firmware.
- The Arm SCMI firmware code gains support for having multiple
instances of firmware running, and better module auto loading.
- A few minor updates for litex, samsung, ti, tegra, mediatek, imx
and renesas platforms.
- Reset controller updates for amlogic, to add support for the A1 soc
and clean up the existing code.
- Memory controller updates for ti davinci aemif, refactoring the
code and adding a few interfaces to other drivers"
* tag 'soc-drivers-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (58 commits)
drivers/soc/litex: Use devm_register_restart_handler()
reset: amlogic: aux: drop aux registration helper
reset: amlogic: aux: get regmap through parent device
reset: amlogic: add support for A1 SoC in auxiliary reset driver
dt-bindings: reset: add bindings for A1 SoC audio reset controller
soc/tegra: fuse: Update Tegra234 nvmem keepout list
soc/tegra: Fix spelling error in tegra234_lookup_slave_timeout()
soc/tegra: cbb: Drop unnecessary debugfs error handling
firmware: qcom: scm: add calls for wrapped key support
soc: qcom: pd_mapper: Add SM7225 compatible
dt-bindings: firmware: qcom,scm: Document ipq5424 SCM
soc: qcom: llcc: Update configuration data for IPQ5424
dt-bindings: cache: qcom,llcc: Add IPQ5424 compatible
soc: mediatek: mtk-devapc: Fix leaking IO map on driver remove
soc: mediatek: mtk-devapc: Fix leaking IO map on error paths
firmware: qcom: scm: smc: Narrow 'mempool' variable scope
firmware: qcom: scm: smc: Handle missing SCM device
firmware: qcom: scm: Cleanup global '__scm' on probe failures
firmware: qcom: scm: Fix missing read barrier in qcom_scm_get_tzmem_pool()
firmware: qcom: scm: Fix missing read barrier in qcom_scm_is_available()
...
|
|
soc/drivers
Reset controller updates for v6.14 (v2)
* Add support for A1 SoC in amlogic reset driver.
* Drop aux registration helper from amlogic reset driver.
* tag 'reset-for-v6.14-2' of git://git.pengutronix.de/pza/linux:
reset: amlogic: aux: drop aux registration helper
reset: amlogic: aux: get regmap through parent device
reset: amlogic: add support for A1 SoC in auxiliary reset driver
dt-bindings: reset: add bindings for A1 SoC audio reset controller
clk: amlogic: axg-audio: revert reset implementation
Revert "clk: Fix invalid execution of clk_set_rate"
Link: https://lore.kernel.org/r/20250115170247.1303656-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Having the aux registration helper along with the registered driver is not
great dependency wise. It does not allow the registering driver to be
properly decoupled from the registered auxiliary driver.
Drop the registration helper from the amlogic auxiliary reset driver.
This will be handled in the registering clock driver to start with while
a more generic solution is worked on.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241209-meson-rst-aux-rework-v1-2-d2afb69cc72e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Get regmap directly from the parent device registering the
auxiliary reset driver, instead of using device data attached
to the auxiliary device.
This simplifies the registration a bit.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241209-meson-rst-aux-rework-v1-1-d2afb69cc72e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for the reset controller present in the audio clock
controller of A1 SoC families, using the auxiliary bus.
Signed-off-by: Jan Dakinevich <jan.dakinevich@salutedevices.com>
Link: https://lore.kernel.org/r/20241112230056.1406222-3-jan.dakinevich@salutedevices.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
arm/fixes
Reset controller fixes for v6.13
* Fix rzg2l-usb-vbus-regulator lookup by assigning the proper of node
to the allocated platform device in the rzg2l-usbphy-ctrl driver.
* tag 'reset-fixes-for-v6.13' of git://git.pengutronix.de/pza/linux:
reset: rzg2l-usbphy-ctrl: Assign proper of node to the allocated device
Link: https://lore.kernel.org/r/20250113163642.1757160-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The platform device named "rzg2l-usb-vbus-regulator", allocated by
the rzg2l-usbphy-ctrl driver, is used to instantiate a regulator driver.
This regulator driver is associated with a device tree (DT) node, which
is a child of the rzg2l-usbphy-ctrl DT node. The regulator's DT node allows
consumer nodes to reference the regulator and configure the regulator as
needed.
Starting with commit cd7a38c40b23 ("regulator: core: do not silently ignore
provided init_data") the struct regulator_dev::dev::of_node is no longer
populated using of_node_get(config->of_node) if the regulator does not
provide init_data. Since the rzg2l-usb-vbus-regulator does not provide
init_data, this behaviour causes the of_find_regulator_by_node() function
to fails, resulting in errors when attempting to request the regulator.
To fix this issue, call device_set_of_node_from_dev() for the
"rzg2l-usb-vbus-regulator" platform device.
Fixes: 84fbd6198766 ("regulator: Add Renesas RZ/G2L USB VBUS regulator driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20241119085554.1035881-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Clean up the existing export namespace code along the same lines of
commit 33def8498fdd ("treewide: Convert macro and uses of __section(foo)
to __section("foo")") and for the same reason, it is not desired for the
namespace argument to be a macro expansion itself.
Scripted using
git grep -l -e MODULE_IMPORT_NS -e EXPORT_SYMBOL_NS | while read file;
do
awk -i inplace '
/^#define EXPORT_SYMBOL_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/^#define MODULE_IMPORT_NS/ {
gsub(/__stringify\(ns\)/, "ns");
print;
next;
}
/MODULE_IMPORT_NS/ {
$0 = gensub(/MODULE_IMPORT_NS\(([^)]*)\)/, "MODULE_IMPORT_NS(\"\\1\")", "g");
}
/EXPORT_SYMBOL_NS/ {
if ($0 ~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+),/) {
if ($0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/ &&
$0 !~ /(EXPORT_SYMBOL_NS[^(]*)\(\)/ &&
$0 !~ /^my/) {
getline line;
gsub(/[[:space:]]*\\$/, "");
gsub(/[[:space:]]/, "", line);
$0 = $0 " " line;
}
$0 = gensub(/(EXPORT_SYMBOL_NS[^(]*)\(([^,]+), ([^)]+)\)/,
"\\1(\\2, \"\\3\")", "g");
}
}
{ print }' $file;
done
Requested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://mail.google.com/mail/u/2/#inbox/FMfcgzQXKWgMmjdFwwdsfgxzKpVHWPlc
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework gained a clk provider helper, a clk consumer
helper, and some unit tests for the assigned clk rates feature in
DeviceTree. On the vendor driver side, we gained a whole pile of SoC
driver support detailed below. The majority in the diffstat is
Qualcomm, but there's also quite a few Samsung and Mediatek clk driver
additions in here as well. The top vendors is quite common, but the
sheer amount of new drivers is uncommon, so I'm anticipating a larger
number of fixes for clk drivers this cycle.
Core:
- devm_clk_bulk_get_all_enabled() to return number of clks acquired
- devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
- KUnit tests for clk-assigned-rates{,-u64}
New Drivers:
- Marvell PXA1908 SoC clks
- Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
- TWL6030 clk driver
- Nuvoton Arbel BMC NPCM8XX SoC clks
- MediaTek MT6735 SoC clks
- MediaTek MT7620, MT7628 and MT7688 MMC clks
- Add a driver for gated fixed rate clocks
- Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
- Camera, display and video clock controllers for Qualcomm SA8775P
SoCs
- Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm
SAR2130P
- Global, camera, display, GPU, and video clock controllers for
Qualcomm SM8475 SoCs
- RTC power domain and Battery Backup Function (VBATTB) clock support
for the Renesas RZ/G3S SoC
- Qualcomm IPQ9574 alpha PLLs
- Support for i.MX91 CCM in the i.MX93 driver
- Microchip LAN969X SoC clks
- Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and
reset on Renesas RZ/V2H(P)
- Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
- Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP
Updates:
- Convert more clk bindings to YAML
- Various clk driver cleanups: NULL checks, add const, etc.
- Remove END/NUM #defines that count number of clks in various
binding headers
- Continue moving reset drivers to drivers/reset via auxiliary bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access
clk: Fix invalid execution of clk_set_rate
clk: clk-loongson2: Fix memory corruption bug in struct loongson2_clk_provider
clk: lan966x: make it selectable for ARCH_LAN969X
clk: eyeq: add EyeQ6H west fixed factor clocks
clk: eyeq: add EyeQ6H central fixed factor clocks
clk: eyeq: add EyeQ5 fixed factor clocks
clk: eyeq: add fixed factor clocks infrastructure
clk: eyeq: require clock index with phandle in all cases
clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
clk: clk-axi-clkgen: make sure to enable the AXI bus clock
dt-bindings: clock: axi-clkgen: include AXI clk
clk: mmp: Add Marvell PXA1908 MPMU driver
clk: mmp: Add Marvell PXA1908 APMU driver
clk: mmp: Add Marvell PXA1908 APBCP driver
clk: mmp: Add Marvell PXA1908 APBC driver
dt-bindings: clock: Add Marvell PXA1908 clock bindings
clk: mmp: Switch to use struct u32_fract instead of custom one
...
|
|
'clk-allwinner' into clk-next
* clk-samsung:
clk: samsung: Introduce Exynos8895 clock driver
clk: samsung: clk-pll: Add support for pll_{1051x,1052x}
dt-bindings: clock: samsung: Add Exynos8895 SoC
clk: samsung: gs101: make all ufs related clocks critical
clk: samsung: exynosautov920: add peric1, misc and hsi0/1 clock support
dt-bindings: clock: exynosautov920: add peric1, misc and hsi0/1 clock definitions
clk: samsung: Fix out-of-bound access of of_match_node()
dt-bindings: clock: samsung: remove define with number of clocks for FSD
clk: samsung: fsd: do not define number of clocks in bindings
clk: samsung: Fix errors reported by checkpatch
clk: samsung: Fix block comment style warnings reported by checkpatch
* clk-microchip:
clk: lan966x: add support for lan969x SoC clock driver
clk: lan966x: prepare driver for lan969x support
clk: lan966x: make clk_names const char * const
dt-bindings: clock: add support for lan969x
* clk-imx:
clk: imx: imx8-acm: Fix return value check in clk_imx_acm_attach_pm_domains()
clk: imx: lpcg-scu: Skip HDMI LPCG clock save/restore
clk: imx: clk-scu: fix clk enable state save and restore
clk: imx: fracn-gppll: fix pll power up
clk: imx: fracn-gppll: correct PLL initialization flow
clk: imx: lpcg-scu: SW workaround for errata (e10858)
clk: imx: add i.MX91 clk
dt-bindings: clock: Add i.MX91 clock support
dt-bindings: clock: imx93: Drop IMX93_CLK_END macro definition
clk: imx93: Move IMX93_CLK_END macro to clk driver
clk: imx95-blk-ctl: Add one clock gate for HSIO block
dt-bindings: clock: nxp,imx95-blk-ctl: Add compatible string for i.MX95 HSIO BLK CTRL
* clk-amlogic:
clk: amlogic: axg-audio: fix Kconfig dependency on RESET_MESON_AUX
clk: amlogic: axg-audio: use the auxiliary reset driver
reset: amlogic: Fix small whitespace issue
reset: amlogic: add auxiliary reset driver support
reset: amlogic: split the device core and platform probe
reset: amlogic: move drivers to a dedicated directory
reset: amlogic: add reset status support
reset: amlogic: use reset number instead of register count
reset: amlogic: add driver parameters
reset: amlogic: make parameters unsigned
reset: amlogic: use generic data matching function
reset: amlogic: convert driver to regmap
dt-bindings: clock: convert amlogic,meson8b-clkc.txt to dtschema
clk: meson: meson8b: remove spinlock
clk: meson: mpll: Delete a useless spinlock from the MPLL
clk: meson: s4: pll: fix frac maximum value for hifi_pll
clk: meson: c3: pll: fix frac maximum value for hifi_pll
clk: meson: Support PLL with fixed fractional denominators
clk: meson: s4: pll: hifi_pll support fractional multiplier
* clk-allwinner:
clk: sunxi-ng: Use of_property_present() for non-boolean properties
clk: sunxi-ng: d1: Fix PLL_AUDIO0 preset
clk: sunxi-ng: Constify struct ccu_reset_map
clk: sunxi-ng: h616: Add sigma-delta modulation settings for audio PLL
|
|
soc/drivers
Reset controller updates for v6.13
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a4b ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79cc
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
* tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux: (21 commits)
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
reset: mchp: sparx5: set the dev member of the reset controller
reset: mchp: sparx5: Allow building as a module
reset: mchp: sparx5: Add MCHP_LAN966X_PCI dependency
reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x
MAINTAINERS: Add the Microchip LAN966x PCI driver entry
misc: Add support for LAN966x PCI device
reset: uniphier-glue: Use devm_reset_control_bulk_get_shared_deasserted()
reset: Add devres helpers to request pre-deasserted reset controls
reset: replace boolean parameters with flags parameter
reset: amlogic: Fix small whitespace issue
reset: amlogic: add auxiliary reset driver support
reset: amlogic: split the device core and platform probe
reset: amlogic: move drivers to a dedicated directory
reset: amlogic: add reset status support
reset: amlogic: use reset number instead of register count
reset: amlogic: add driver parameters
reset: amlogic: make parameters unsigned
reset: amlogic: use generic data matching function
...
Link: https://lore.kernel.org/r/20241105105229.3729474-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
In order to guarantee the device will not be deleted by the reset
controller consumer, set the dev member of the reset controller.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20241014124636.24221-7-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This reset controller can be used by the LAN966x PCI device.
The LAN966x PCI device driver can be built as a module and this reset
controller driver has no reason to be a builtin driver in that case.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20241014124636.24221-6-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The sparx5 reset controller depends on the SPARX5 architecture or the
LAN966x SoC.
This reset controller can be used by the LAN966x PCI device and so it
needs to be available when the LAN966x PCI device is enabled.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20241014124636.24221-5-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
In the LAN966x PCI device use case, the syscon API cannot be used as
it does not support device removal [1]. A syscon device is a core
"system" device and not a device available in some addon boards and so,
it is not supposed to be removed. The syscon API follows this assumption
but this assumption is no longer valid in the LAN966x use case.
In order to avoid the use of the syscon API and so, support for removal,
use a local mapping of the syscon device.
Link: https://lore.kernel.org/all/20240923100741.11277439@bootlin.com/ [1]
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20241014124636.24221-4-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add NPCM8xx clock controller auxiliary bus device registration.
The NPCM8xx clock controller is registered as an aux device because the
reset and the clock controller share the same register region.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Benjamin Fair <benjaminfair@google.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240912191038.981105-3-tmaimon77@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Replace the pattern devm_reset_control_bulk_get_shared() /
reset_control_bulk_deassert() / devm_add_action_or_reset()
with devm_reset_control_bulk_get_shared_deasserted() for
some reduction in boilerplate.
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240925-reset-get-deasserted-v2-3-b3601bbd0458@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add devres helpers
- devm_reset_control_bulk_get_exclusive_deasserted
- devm_reset_control_bulk_get_optional_exclusive_deasserted
- devm_reset_control_bulk_get_optional_shared_deasserted
- devm_reset_control_bulk_get_shared_deasserted
- devm_reset_control_get_exclusive_deasserted
- devm_reset_control_get_optional_exclusive_deasserted
- devm_reset_control_get_optional_shared_deasserted
- devm_reset_control_get_shared_deasserted
to request and immediately deassert reset controls. During cleanup,
reset_control_assert() will be called automatically on the returned
reset controls.
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240925-reset-get-deasserted-v2-2-b3601bbd0458@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Introduce enum reset_control_flags and replace the list of boolean
parameters to the internal reset_control_get functions with a single
flags parameter, before adding more boolean options.
The separate boolean parameters have been shown to be error prone in
the past. See for example commit a57f68ddc886 ("reset: Fix devm bulk
optional exclusive control getter").
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240925-reset-get-deasserted-v2-1-b3601bbd0458@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Fix a checkpatch --strict issue:
CHECK: Alignment should match open parenthesis
#48: FILE: drivers/reset/amlogic/reset-meson-common.c:48:
+static int meson_reset_level(struct reset_controller_dev *rcdev,
+ unsigned long id, bool assert)
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240930-reset-align-amlogic-v1-1-f64ed5c4efc1@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for the reset controller present in the audio clock
controller of the g12 and sm1 SoC families, using the auxiliary bus.
This is expected to replace the driver currently present directly
within the related clock driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-9-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
To prepare the addition of the auxiliary device support, split
out the device coomon functions from the probe of the platform device.
The device core function will be common to both the platform and auxiliary
driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-8-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The meson reset driver will be split in two part, one implemeting the ops,
the other providing the platform driver support. This will be done to
facilitate the addition of the auxiliary bus support.
To avoid making a mess in drivers/reset/ while doing so, move the amlogic
reset drivers to a dedicated directory.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-7-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add a callback to check the status of the level reset, as done in
the reset driver of the audio clock controller.
This is done keep the functionality when the audio reset controller
get migrated to meson-reset.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-6-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The reset driver from audio clock controller may register less
reset than a register can hold. To avoid making any change while
switching to auxiliary support, use the number of reset instead of the
register count to define the bounds of the reset controller.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-5-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
To allow using the same driver for the main reset controller and the
auxiliary ones embedded in the clock controllers, allow to customise
the reset offset, same as the level offset. Also add an option to make
the level reset active low or high.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-4-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
register count and offset cannot be negative. Use unsigned integer
for this.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-3-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
There is no need to use the DT specific function to get
matching data, use the generic one instead
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-2-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
To allow using the same driver for the main reset controller and the
auxiliary ones embedded in the clock controllers, convert the
the Amlogic reset driver to regmap.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240910-meson-rst-aux-v5-1-60be62635d3e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
data->asserted will be NULL on JH7110 SoC since commit 82327b127d41
("reset: starfive: Add StarFive JH7110 reset driver") was added. Add
the judgment condition to avoid errors when calling reset_control_status
on JH7110 SoC.
Fixes: 82327b127d41 ("reset: starfive: Add StarFive JH7110 reset driver")
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Acked-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240925112442.1732416-1-changhuang.liang@starfivetech.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240909061258.2246292-1-yanzhen@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add Mobileye EyeQ reset controller driver, for EyeQ5, EyeQ6L and EyeQ6H
SoCs. Instances belong to a shared register region called OLB and gets
spawned as auxiliary device to the platform driver for clock.
There is one OLB instance for EyeQ5 and EyeQ6L. There are seven OLB
instances on EyeQ6H; three have a reset controller embedded:
- West and east get handled by the same compatible.
- Acc (accelerator) is another one.
Each instance vary in the number and types of reset domains.
Instances with single domain expect a single cell, others two.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240730-mbly-reset-v2-2-00b870a6a2ff@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
There are 7 sets of Reset Source in Amlogic T7 SoC reset controller,
and the offset between base and level registers is 0x40.
Add a new compatible string and struct meson_reset_param to support
the reset controller on T7 SoC.
Signed-off-by: Zelong Dong <zelong.dong@amlogic.com>
Signed-off-by: Kelvin Zhang <kelvin.zhang@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240422-t7-reset-v2-2-cb82271d3296@amlogic.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Since the rcdev structure is allocated by the reset controller drivers
themselves, they need to exists as long as there is a consumer. A call to
module_get() is already existing but that does not work when using
device-tree overlays. In order to guarantee that the underlying reset
controller device does not vanish while using it, add a get_device() call
when retrieving a reset control from a reset controller device and a
put_device() when releasing that control.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240808154658.247873-8-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use devm_clk_get_enabled() to drop clock prepare/unprepare parts and
make the code simpler. Change to dev_err_probe() in handling
reset_controller_register() error to make it even simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20240825-reset-cleanup-scoped-v1-5-03f6d834f8c0@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use dev_err_probe() to avoid dmesg flood on actual defer. This makes
the code also simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20240825-reset-cleanup-scoped-v1-4-03f6d834f8c0@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Simplify error handling (less gotos) over locks with guard().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240825-reset-cleanup-scoped-v1-3-03f6d834f8c0@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Driver is leaking OF node reference on memory allocation failure.
Acquire the OF node reference after memory allocation to fix this and
keep it simple.
Fixes: 5a2308da9f60 ("riscv: Add Canaan Kendryte K210 reset controller")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240825-reset-cleanup-scoped-v1-2-03f6d834f8c0@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Driver is leaking OF node reference on memory allocation failure.
Acquire the OF node reference after memory allocation to fix this and
keep it simple.
Fixes: aed6f3cadc86 ("reset: berlin: convert to a platform driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240825-reset-cleanup-scoped-v1-1-03f6d834f8c0@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
|
|
As per RZ/G2L HW manual, VBUS enable can be controlled by the VBOUT bit
of the VBUS Control Register(VBENCTL) register in the USBPHY Control.
Expose this register as regmap and instantiate the USB VBUS regulator
device, so that consumer can control the vbus using regulator API's
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240702180032.207275-3-biju.das.jz@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The Tegra BPMP reset driver can be compiled without TEGRA_BPMP being
enabled. Allow it to be built under COMPILE_TEST.
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240625-reset-compile-bpmp-v1-1-647e846303d8@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The i.MX8MP AudioMix reset controller is only present on Freescale i.MX8
SoCs. Hence add a dependency on ARCH_MXC, to prevent asking the user
about this driver when configuring a kernel without i.MX SoC support.
Fixes: fe125601d17cc1ea ("reset: imx8mp-audiomix: Add AudioMix Block Control reset driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/6d8116a56186fbf468229e823c7c8dfcd9488959.1719316665.git.geert+renesas@glider.be
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The ZynqMP reset driver can be compiled without ARCH_ZYNQMP being
enabled. Allow it to be built under COMPILE_TEST.
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240621-reset-compile-zynqmp-v1-1-ede43ab18101@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for the resets on i.MX8MP Audio Block Control module,
which includes the EARC PHY software reset and EARC controller
software reset. The reset controller is created using the auxiliary
device framework and set up in the clock driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1719200345-32006-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use devm_clk_get_enabled() to reduce a bit of boilerplate and to
disable the clock in case devm_reset_controller_register() fails.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240621-reset-devm-clk-get-enabled-v1-1-8408c7962b6c@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The STIH407 reset driver can be compiled without ARCH_STI being
enabled. Allow it to be built under COMPILE_TEST.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240621-reset-compile-sti-v1-1-b7a66ce29911@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
As soon as the reset controller is registered, it could be used by a
reset consumer. That means hardware setup to be done first and then the
registration of the reset controller. So move the registration of reset
controller at the end of probe().
While at it, fix the issue that the reset is not re-asserted in case
devm_reset_controller_register() fails and also use goto statements to
simplify the error path in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240610164845.89666-1-biju.das.jz@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/reset/hisilicon/hi6220_reset.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-reset-v1-1-5d317ff8e3bd@quicinc.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The GPIO reset controller uses gpiolib but there is no Kconfig
dependency reflecting this fact, add one.
With the addition of the controller to the arm64 defconfig this is
causing build breaks for arm64 virtconfig in -next:
aarch64-linux-gnu-ld: drivers/reset/core.o: in function `__reset_add_reset_gpio_lookup':
/build/stage/linux/drivers/reset/core.c:861:(.text+0xccc): undefined reference to `gpio_device_find_by_fwnode'
Fixes: cee544a40e44 ("reset: gpio: Add GPIO-based reset controller")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240325-reset-gpiolib-deps-v2-1-3ed2517f5f53@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Philipp didn't come around to send a pull request in the last
development cycle. His next branch only contains patches converting
three platform drivers to stop using .remove().
They are merged with his consent to be able to change the prototype of
.remove() in the upcoming development cycle.
Link: https://lore.kernel.org/all/9b7e1a88a812f5c86ada75b094c95b9cf65891c3.camel@pengutronix.de/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"I'm actually surprised this time. There aren't any new Qualcomm SoC
clk drivers. And there's zero diff in the core clk framework.
Instead we have new clk drivers for STM and Sophgo, with
Samsung^WGoogle in third for the diffstat because they introduced HSI0
and HSI2 clk drivers for Google's GS101 SoC (high speed interface
things like PCIe, UFS, and MMC).
Beyond those big diffs there's the usual updates to various clk
drivers for incorrect parent descriptions or mising
MODULE_DEVICE_TABLE()s, etc. Nothing in particular stands out as super
interesting here.
New Drivers:
- STM32MP257 SoC clk driver
- Airoha EN7581 SoC clk driver
- Sophgo CV1800B, CV1812H and SG2000 SoC clk driver
- Loongson-2k0500 and Loongson-2k2000 SoC clk driver
- Add HSI0 and HSI2 clock controllers for Google GS101
- Add i.MX95 BLK CTL clock driver
Updates:
- Allocate clk_ops dynamically for SCMI clk driver
- Add support in qcom RCG and RCG2 for multiple configurations for
the same frequency
- Use above support for IPQ8074 NSS port 5 and 6 clocks to resolve
issues
- Fix the Qualcomm APSS IPQ5018 PLL to fix boot failures of some
boards
- Cleanups and fixes for Qualcomm Stromer PLLs
- Reduce max CPU frequency on Qualcomm APSS IPQ5018
- Fix Kconfig dependencies of Qualcomm SM8650 GPU and SC8280XP camera
clk drivers
- Make Qualcomm MSM8998 Venus clocks functional
- Cleanup downstream remnants related to DisplayPort across Qualcomm
SM8450, SM6350, SM8550, and SM8650
- Reuse the Huayra APSS register map on Qualcomm MSM8996 CBF PLL
- Use a specific Qualcomm QCS404 compatible for the otherwise generic
HFPLL
- Remove Qualcomm SM8150 CPUSS AHB clk as it is unused
- Remove an unused field in the Qualcomm RPM clk driver
- Add missing MODULE_DEVICE_TABLE to Qualcomm MSM8917 and MSM8953
global clock controller drivers
- Allow choice of manual or firmware-driven control over PLLs, needed
to fully implement CPU clock controllers on Exynos850
- Correct PLL clock IDs on ExynosAutov9
- Propagate certain clock rates to allow setting proper SPI clock
rates on Google GS101
- Mark certain Google GS101 clocks critical
- Convert old S3C64xx clock controller bindings to DT schema
- Add new PLL rate and missing mux on Rockchip rk3568
- Add missing reset line on Rockchip rk3588
- Removal of an unused field in struct rockchip_mmc_clock
- Amlogic s4/a1: add regmap maximum register for proper debugfs dump
- Amlogic s4: add MODULE_DEVICE_TABLE() on pll and periph controllers
- Amlogic pll driver: print clock name on lock error to help debug
- Amlogic vclk: finish dsi clock path support
- Amlogic license: fix occurence "GPL v2" as reported by checkpatch
- Add PM runtime support to i.MX8MP Audiomix
- Add DT schema for i.MX95 Display Master Block Control
- Convert to platform remove callback returning void for i.MX8MP
Audiomix
- Add SPI (MSIOF) and external interrupt (INTC-EX) clocks on Renesas
R-Car V4M
- Add interrupt controller (PLIC) clock and reset on Renesas RZ/Five
- Prepare power domain support for Renesas RZ/G2L family members, and
add actual support on Renesas RZ/G3S SoC
- Add thermal, serial (SCIF), and timer (CMT/TMU) clocks on Renesas
R-Car V4M
- Add additional constraints to Allwinner A64 PLL MIPI clock
- Fix autoloading sunxi-ng clocks when build as a module"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (118 commits)
clk: samsung: Don't register clkdev lookup for the fixed rate clocks
clk, reset: microchip: mpfs: fix incorrect preprocessor conditions
clk: qcom: clk-alpha-pll: fix rate setting for Stromer PLLs
clk: qcom: apss-ipq-pll: fix PLL rate for IPQ5018
clk: qcom: Fix SM_GPUCC_8650 dependencies
clk: qcom: Fix SC_CAMCC_8280XP dependencies
dt-bindings: clocks: stm32mp25: add access-controllers description
clock, reset: microchip: move all mpfs reset code to the reset subsystem
clk: samsung: gs101: drop unused HSI2 clock parent data
clk: rockchip: rk3568: Add PLL rate for 724 MHz
clk: rockchip: Remove an unused field in struct rockchip_mmc_clock
dt-bindings: clock: fixed: Define a preferred node name
clk: meson: s4: fix module autoloading
clk: samsung: gs101: mark some apm UASC and XIU clocks critical
clk: imx: imx8mp: Convert to platform remove callback returning void
clk: imx: imx8mp: Switch to RUNTIME_PM_OPS()
clk: bcm: rpi: Assign ->num before accessing ->hws
clk: bcm: dvp: Assign ->num before accessing ->hws
clk: samsung: gs101: add support for cmu_hsi2
clk: samsung: gs101: add support for cmu_hsi0
...
|
|
Stephen and Philipp, while reviewing patches, said that all of the aux
device creation and the register read/write code could be moved to the
reset subsystem, leaving the clock driver with no implementations of
reset_* functions at all. Move them.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240424-strangle-sharpener-34755c5e6e3e@spud
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since SOC_FOO should be deprecated from patch [1], and cleanup for other
SoCs is already in the mailing list [2,3,4,5], we remove the use of
SOC_CANAAN and introduced SOC_CANAAN_K210 for K210-specific drivers,
Thus, we replace its drivers depends on SOC_CANAAN_K210 and default select
when it has the symbol SOC_CANAAN_K210.
[1] https://lore.kernel.org/linux-riscv/20221121221414.109965-1-conor@kernel.org/
[2] https://lore.kernel.org/linux-riscv/20240305-praying-clad-c4fbcaa7ed0a@spud/
[3] https://lore.kernel.org/linux-riscv/20240305-fled-undrilled-41dc0c46bb29@spud/
[4] https://lore.kernel.org/linux-riscv/20240305-stress-earflap-d7ddb8655a4d@spud/
[5] https://lore.kernel.org/linux-riscv/20240305-praying-clad-c4fbcaa7ed0a@spud/
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/ab374da386cafd6748aac5bdf66e6be3e1860509.1709674157.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/e75fb1af5c7df5fc4073a26a99ba88633503910d.1709674157.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/dbca07bad345abe7ca421515004987acf1cb41c2.1709674157.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Devices sharing a reset GPIO could use the reset framework for
coordinated handling of that shared GPIO line. We have several cases of
such needs, at least for Devicetree-based platforms.
If Devicetree-based device requests a reset line, while "resets"
Devicetree property is missing but there is a "reset-gpios" one,
instantiate a new "reset-gpio" platform device which will handle such
reset line. This allows seamless handling of such shared reset-gpios
without need of changing Devicetree binding [1].
To avoid creating multiple "reset-gpio" platform devices, store the
Devicetree "reset-gpios" GPIO specifiers used for new devices on a
linked list. Later such Devicetree GPIO specifier (phandle to GPIO
controller, GPIO number and GPIO flags) is used to check if reset
controller for given GPIO was already registered.
If two devices have conflicting "reset-gpios" property, e.g. with
different ACTIVE_xxx flags, this would allow to spawn two separate
"reset-gpio" devices, where the second would fail probing on busy GPIO
request.
Link: https://lore.kernel.org/all/YXi5CUCEi7YmNxXM@robh.at.kernel.org/ [1]
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240129115216.96479-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add a simple driver to control GPIO-based resets using the reset
controller API for the cases when the GPIOs are shared and reset should
be coordinated. The driver is expected to be used by reset core
framework for ad-hoc reset controllers.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240129115216.96479-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Reuse reset-simple driver for the Sophgo SG2042 reset generator.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/1cfd7b3ba447942784c4f7aa595e962399e9f617.1706577450.git.unicorn_wang@outlook.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
|
|
When obtaining one or more optional resets, non-existent resets are
stored as NULL pointers, and all related error and cleanup paths need to
take this into account.
Currently only reset_control_put() and reset_control_bulk_put()
get this right. All of __reset_control_bulk_get(),
of_reset_control_array_get(), and reset_control_array_put() lack the
proper checking, causing NULL pointer dereferences on failure or
release.
Fix this by moving the existing check from reset_control_bulk_put() to
__reset_control_put_internal(), so it applies to all callers.
The double check in reset_control_put() doesn't hurt.
Fixes: 17c82e206d2a3cd8 ("reset: Add APIs to manage array of resets")
Fixes: 48d71395896d54ee ("reset: Add reset_control_bulk API")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2440edae7ca8534628cdbaf559ded288f2998178.1701276806.git.geert+renesas@glider.be
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20231115205848.3732609-1-robh@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add a new compatible string to support for the reset controller
on the C3 SoC. The count and offset for C3 Soc RESET registers are
same as S4 Soc.
Signed-off-by: Zelong Dong <zelong.dong@amlogic.com>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230914064018.18790-3-zelong.dong@amlogic.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704120211.38122-7-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704120211.38122-6-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704120211.38122-5-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704120211.38122-4-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704120211.38122-3-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230704120211.38122-2-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230704120211.38122-1-frank.li@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
hi6220_reset.c:166:9: error: cast to smaller integer type 'enum hi6220_reset_ctrl_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810091300.70197-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct reset_control_array.
Additionally, since the element count member must be set before accessing
the annotated flexible array member, move its initialization earlier.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175229.work.838-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"This pull request is full of clk driver changes. In fact, there aren't
any changes to the clk framework this time around. That's probably
because everyone was on vacation (yours truly included). We did lose a
couple clk drivers this time around because nobody was using those
devices. That skews the diffstat a bit, but either way, nothing looks
out of the ordinary here. The usual suspects are chugging along adding
support for more SoCs and fixing bugs.
If I had to choose, I'd say the theme for the past few months has been
"polish". There's quite a few patches that migrate to
devm_platform_ioremap_resource() in here. And there's more than a
handful of patches that move the NR_CLKS define from the DT binding
header to the driver. There's even patches that migrate drivers to use
clk_parent_data and clk_hw to describe clk tree topology. It seems
that the spring (summer?) cleaning bug got some folks, or the
semiconductor shortage finally hit the software side.
New Drivers:
- StarFive JH7110 SoC clock drivers
- Qualcomm IPQ5018 Global Clock Controller driver
- Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
Removed Drivers:
- Remove non-OF mmp clk drivers
- Remove OXNAS clk driver
Updates:
- Add __counted_by to struct clk_hw_onecell_data and struct
spmi_pmic_div_clk_cc
- Move defines for numbers of clks (NR_CLKS) from DT headers to
drivers
- Introduce kstrdup_and_replace() and use it
- Add PLL rates for Rockchip rk3568
- Add the display clock tree for Rockchip rv1126
- Add Audio Clock Generator (ADG) clocks on Renesas R-Car Gen3 and
RZ/G2 SoCs
- Convert sun9i-mmc clock to use
devm_platform_get_and_ioremap_resource()
- Fix function name in a comment in ccu_mmc_timing.c
- Parameter name correction for ccu_nkm_round_rate()
- Implement CLK_SET_RATE_PARENT for Allwinner NKM clocks, i.e.
consider alternative parent rates when determining clock rates
- Set CLK_SET_RATE_PARENT for Allwinner A64 pll-mipi
- Support finding closest (as opposed to closest but not higher)
clock rate for NM, NKM, mux and div type clocks, as use it for
Allwinner A64 pll-video0
- Prefer current parent rate if able to generate ideal clock rate for
Allwinner NKM clocks
- Clean up Qualcomm SMD RPM driver, with interconnect bus clocks
moved out to the interconnect drivers
- Fix various PM runtime bugs across many Qualcomm clk drivers
- Migrate Qualcomm MDM9615 is to parent_hw and parent_data
- Add network related resets on Qualcomm IPQ4019
- Add a couple missing USB related clocks to Qualcomm IPQ9574
- Add missing gpll0_sleep_clk_src to Qualcomm MSM8917 global clock
controller
- In the Qualcomm QDU1000 global clock controller, GDSCs, clkrefs,
and GPLL1 are added, while PCIe pipe clock, SDCC rcg ops are
corrected
- Add missing GDSCs to and correct GDSCs for the SC8280XP global
clock controller driver
- Support retention for the Qualcomm SC8280XP display clock
controller GDSCs.
- Qualcommm's SDCC apps_clk_src is marked with CLK_OPS_PARENT_ENABLE
to fix issues with missing parent clocks across sc7180, sm7150,
sm6350 and sm8250, while sm8450 is corrected to use floor ops
- Correct Qualcomm SM6350 GPU clock controller's clock supplies
- Drop unwanted clocks from the Qualcomm IPQ5332 GCC driver
- Add missing OXILICX GDSC to Qualcomm MSM8226 GCC
- Change the delay in the Qualcomm reset controller to fsleep() for
correctness
- Extend the Qualcomm SM83550 Video clock controller to support
SC8280XP
- Add graphics clock support on Renesas RZ/G2M, RZ/G2N, RZ/G2E, and
R-Car H3, M3-W, and M3-N SoCs
- Add Clocked Serial Interface (CSI) clocks on Renesas RZ/V2M
- Add PWM (MTU3) clock and reset on Renesas RZ/G2UL and RZ/Five
- Add the PDM IPC clock for i.MX93
- Add 519.75MHz frequency support for i.MX9 PLL
- Simplify the .determine_rate() implementation for i.MX GPR mux
- Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource()
- Add the audio mux clock to i.MX8
- Fix the SPLL2 MULT range for PLLv4
- Update the SPLL2 type in i.MX8ULP
- Fix the SAI4 clock on i.MX8MP
- Add silicon revision print for i.MX25 on clocks init
- Drop the return value from __mx25_clocks_init()
- Fix the clock pauses on no-op set_rate for i.MX8M composite clock
- Drop restrictions for i.MX PLL14xx and fix its max prediv value
- Drop the 393216000 and 361267200 from i.MX PLL14xx rate table to
allow glitch free switching"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (207 commits)
clk: qcom: Fix SM_GPUCC_8450 dependencies
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
clk: mvebu: Convert to devm_platform_ioremap_resource()
clk: nuvoton: Convert to devm_platform_ioremap_resource()
clk: socfpga: agilex: Convert to devm_platform_ioremap_resource()
clk: ti: Use devm_platform_get_and_ioremap_resource()
clk: mediatek: Convert to devm_platform_ioremap_resource()
clk: hsdk-pll: Convert to devm_platform_ioremap_resource()
clk: gemini: Convert to devm_platform_ioremap_resource()
clk: fsl-sai: Convert to devm_platform_ioremap_resource()
clk: bm1880: Convert to devm_platform_ioremap_resource()
clk: axm5516: Convert to devm_platform_ioremap_resource()
clk: actions: Convert to devm_platform_ioremap_resource()
clk: cdce925: Remove redundant of_match_ptr()
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
...
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230807111534.12392-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230807114344.15076-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230807113545.14743-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230807112705.12862-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230807105630.11638-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230807105400.11560-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230807104549.11225-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230803104225.29740-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230803104142.29694-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230803104102.29647-1-aboutphysycs@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The probe process may generate EPROBE_DEFER. In this case,
dev_err_probe can still record err information.
This helps simplify code and standardize error output.
Signed-off-by: Wang Ming <machel@vivo.com>
Link: https://lore.kernel.org/r/20230726114555.5011-1-machel@vivo.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Updated the reset driver to support Versal NET platform.
As part of adding support for versal NET:
- Added Versal NET specific compatible string.
- Reset Id and number of resets.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230721041119.4058430-3-piyush.mehta@amd.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230714174939.4063667-1-robh@kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add new struct members and auxiliary_device_id of resets to support
System-Top-Group, Image-Signal-Process and Video-Output on the StarFive
JH7110 SoC.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Link: https://lore.kernel.org/r/20230724055440.100947-1-xingyu.wu@starfivetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
|
|
The Nuvoton MA35D1 reset controller is only present on Nuvoton MA35
SoCs. Hence add a dependency on ARCH_MA35, to prevent asking the user
about this driver when configuring a kernel without MA35 SoC support.
Also, do not enable the driver by default when merely compile-testing.
While at it, fix a misspelling of "Nuvoton".
Fixes: e4bb55d6ccf0f774 ("reset: Add Nuvoton ma35d1 reset driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This driver supports individual IP reset for the MA35D1. The reset
control registers are a subset of the system control registers.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
CONFIG_AUXILIARY_BUS is not a user-visible symbol, replace 'depends on'
with 'select'.
Cc: Daire McNamara <daire.mcnamara@microchip.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230502102041.1418397-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
CONFIG_AUXILIARY_BUS is not a user-visible symbol, replace 'depends on'
with 'select'.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20230502102050.1418417-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Due to lack of maintainance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for OX810 and OX820 peripheral reset.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230331-topic-oxnas-upstream-remove-v1-17-5bd58fd1dd1f@linaro.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
With commit 64933513e461 ("reset: sti: Remove STiH415/6 reset support"),
there is only one sti reset driver left and there no need to define a
dedicated config STI_RESET_SYSCFG, which is selected by the config for the
STiH407 reset driver.
Simply add reset-syscfg.c to the build for the STiH407 reset driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20230330112347.31137-2-lukas.bulwahn@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/202303231653447704556@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use regmap_field_read_poll_timeout function when waiting for the
ack bit upon performing the reset control.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20230210224332.98482-1-avolmat@me.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/202302161052126378140@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/202302161054598138273@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302161056304138337@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302161053360618204@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302161050336958071@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly
what this function does.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202302161049100728015@zte.com.cn
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing looks out of the ordinary in this batch of clk driver updates.
There are a couple patches to the core clk framework, but they're all
basically cleanups or debugging aids. The driver updates and new
additions are dominated in the diffstat by Qualcomm and MediaTek
drivers. Qualcomm gained a handful of new drivers for various SoCs,
and MediaTek gained a bunch of drivers for MT8188. The MediaTek
drivers are being modernized as well, so there are updates all over
that vendor's clk drivers. There's also a couple other new clk drivers
in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual
collection of non-critical fixes and cleanups to various clk drivers.
It's good to see that we're getting more cleanups and modernization
patches. Maybe one day we'll be able to properly split clk providers
from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574,
MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P
SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent
failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP
to get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code
to common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car
V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm
SM6375, MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip
rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (290 commits)
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
clk: starfive: Delete the redundant dev_set_drvdata() in JH7110 clock drivers
clk: rockchip: rk3588: make gate linked clocks critical
clk: qcom: dispcc-qcm2290: Remove inexistent DSI1PHY clk
clk: qcom: add the GPUCC driver for sa8775p
dt-bindings: clock: qcom: describe the GPUCC clock for SA8775P
clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
clk: qcom: lpassaudiocc-sc7280: Add required gdsc power domain clks in lpass_cc_sc7280_desc
clk: qcom: lpasscc-sc7280: Skip qdsp6ss clock registration
dt-bindings: clock: qcom,sc7280-lpasscc: Add qcom,adsp-pil-mode property
clk: starfive: Avoid casting iomem pointers
clk: microchip: fix potential UAF in auxdev release callback
clk: qcom: rpm: Use managed `of_clk_add_hw_provider()`
clk: mediatek: fhctl: Mark local variables static
clk: sifive: make SiFive clk drivers depend on ARCH_ symbols
clk: uniphier: Use managed `of_clk_add_hw_provider()`
clk: si5351: Use managed `of_clk_add_hw_provider()`
clk: si570: Use managed `of_clk_add_hw_provider()`
clk: si514: Use managed `of_clk_add_hw_provider()`
clk: lmk04832: Use managed `of_clk_add_hw_provider()`
...
|
|
Let's use a wrapper struct for the auxiliary_device made in
jh7110_reset_controller_register() so that we can stop casting iomem
pointers. The casts trip up tools like sparse, and make for some awkward
casts that are largely unnecessary. While we're here, change the
allocation from devm and actually free the auxiliary_device memory in
the release function. This avoids any use after free problems where the
parent device driver is unbound from the device but the
auxiliuary_device is still in use accessing devm freed memory.
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Cc: Hal Feng <hal.feng@starfivetech.com>
Cc: Conor Dooley <conor.dooley@microchip.com>
Cc: Xingyu Wu <xingyu.wu@starfivetech.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Fixes: edab7204afe5 ("clk: starfive: Add StarFive JH7110 system clock driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230413205528.4044216-1-sboyd@kernel.org
|
|
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Conor Dooley <conor.dooley@microchip.com>
Cc: Daire McNamara <daire.mcnamara@microchip.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: Daniel Machon <daniel.machon@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Add auxiliary driver to support StarFive JH7110 system
and always-on resets.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
We currently use 64bit I/O on the 32bit registers. This works because
there are an even number of assert and status registers, so they're only
ever accessed in pairs on 64bit boundaries.
There are however other reset controllers for audio and video on the
JH7100 SoC with only one status register that isn't 64bit aligned so
64bit I/O results in an unaligned access exception.
Switch to 32bit I/O in preparation for supporting these resets too.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
For the common code will be shared with the StarFive JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Extract the common JH71X0 reset code for reusing them to
support JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The StarFive JH7100 SoC has additional reset controllers for audio and
video, but the registers follow the same structure. On the JH7110 the
reset registers don't get their own memory range, but instead follow the
clock control registers. The registers still follow the same structure
though, so let's factor out the common code to handle all these cases.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This moves the StarFive JH7100 reset driver to a new subdirectory in
preparation for adding more StarFive reset drivers.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Using ARCH_FOO symbol is preferred than SOC_FOO.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
It will cause null-ptr-deref when resource_size(res) invoked,
if platform_get_resource() returns NULL.
Fixes: 499fef09a323 ("reset: uniphier: add USB3 core reset control")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221114004958.258513-1-tanghui20@huawei.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
There is a build error when COMPILE_TEST=y, TI_SCI_PROTOCOL=m,
and RESET_TI_SCI=y:
drivers/reset/reset-ti-sci.o: in function `ti_sci_reset_probe':
reset-ti-sci.c:(.text+0x22c): undefined reference to `devm_ti_sci_get_handle'
Fix this by making RESET_TI_SCI honor the Kconfig setting of
TI_SCI_PROTOCOL when COMPILE_TEST is not set. When COMPILE_TEST is set,
TI_SCI_PROTOCOL must be disabled (=n).
Fixes: a6af504184c9 ("reset: ti-sci: Allow building under COMPILE_TEST")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221030055636.3139-1-rdunlap@infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
|
|
In NPCM8XX USB reset sequence, iprst2 register was set with iprst4 value
and iprst4 register wasn´t set.
This fix sets the correct IP reset values in iprst2 and iprst4 registers
in NPCM8XX USB reset sequence.
Fixes: fc5d2a2f4aa5 ("reset: npcm: Add NPCM8XX support")
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220922153856.23326-1-tmaimon77@gmail.com
|
|
Add support for the resets on Microchip's PolarFire SoC (MPFS).
Reset control is a single register, wedged in between registers for
clock control. To fit with existed DT etc, the reset controller is
created using the aux device framework & set up in the clock driver.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909123123.2699583-6-conor.dooley@microchip.com
|
|
Originally this was used in by the switch core driver to issue a reset.
But it turns out, this isn't just a switch core reset but instead it
will reset almost the complete SoC.
Instead of adding almost all devices of the SoC a shared reset line,
issue the reset once early on startup. Keep the reset controller for
backwards compatibility, but make the actual reset a noop.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Steen Hegelund <Steen.Hegelund@microchip.com> on Sparx5
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220826115607.1148489-2-michael@walle.cc
|
|
On i.MX7/iMX8MM/iMX8MQ, the initialized default value of PERST bit(BIT3)
of SRC_PCIEPHY_RCR is 1b'1.
But i.MX8MP has one inversed default value 1b'0 of PERST bit.
And the PERST bit should be kept 1b'1 after power and clocks are stable.
So fix the i.MX8MP PCIe PHY PERST support here.
Fixes: e08672c03981 ("reset: imx7: Add support for i.MX8MP SoC")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/1661845564-11373-5-git-send-email-hongxing.zhu@nxp.com
|
|
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"These updates came in after I had already tagged the branches, but
they still seem appropriate for 6.0 and most of them were part of
linux-next through other trees.
- The reset controller tree adds one new driver for the TI TPS380x
power management chip and a few minor changes in other drivers
- Apple M1 now has a DT entry for the NVMe controller after the
driver was merged, and has a new mailing list in the MAINTAINERS
file.
- Fixes for USB on the Socionext Uniphier platforms and the network
controller on Intel Cyclone5"
* tag 'arm-late-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: uniphier: Fix USB interrupts for PXs3 SoC
ARM: dts: uniphier: Fix USB interrupts for PXs2 SoC
arm64: dts: apple: t8103: Add ANS2 NVMe nodes
reset: tps380x: Fix spelling mistake "Voltags" -> "Voltage"
reset: tps380x: Add TPS380x device driver supprt
dt-bindings: reset: Add TPS380x documentation
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G2UL USBPHY Control bindings
ARM: dts: add EMAC AXI settings for Cyclone5
reset: reset-simple should depends on HAS_IOMEM
Revert "reset: microchip-sparx5: allow building as a module"
reset: a10sr: allow building under COMPILE_TEST
reset: allow building of reset simple driver if expert config selected
reset: microchip-sparx5: allow building as a module
arm64: dts: apple: Re-parent ANS2 power domains
MAINTAINERS: add ARM/APPLE MACHINE mailing list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
|
|
There is a spelling mistake in the MODULE_DESCRIPTION text. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220728110554.18320-1-colin.i.king@gmail.com
|
|
The TI TPS380x family [1] is a voltage supervisor with a dedicated
manual reset (mr) line input and a reset output. The chip(s) have a
build in reset delay, depending on the chip partnumber. This simple
driver addresses this so the cosumer don't need to care about it.
[1] https://www.ti.com/product/TPS3801
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[p.zabel@pengutronix.de: drop Todo comment about min/typ/max reset time]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220530092226.748644-2-m.felsch@pengutronix.de
|
|
The reset-simple driver does not build on all architecuters as it requires
devm_ioremap_resource() which is only built when CONFIG_HAS_IOMEM is enabled
in the kenrel. Fix the following error by depending on CONFIG_HAS_IOMEM:
drivers/reset/reset-simple.o: in function `reset_simple_probe':
reset-simple.c:(.text+0x3aa): undefined reference to `devm_ioremap_resource'
Fixes: 18d1909be345 ("reset: allow building of reset simple driver if expert config selected")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220719085200.203688-1-ben.dooks@sifive.com
|
|
Merge the new SoC support from Tomer Maimon:
"This patchset adds initial support for the Nuvoton
Arbel NPCM8XX Board Management controller (BMC) SoC family.
The Nuvoton Arbel NPCM8XX SoC is a fourth-generation BMC.
The NPCM8XX computing subsystem comprises a quadcore ARM
Cortex A35 ARM-V8 architecture.
This patchset adds minimal architecture and drivers such as:
Clocksource, Clock, Reset, and WD.
Some of the Arbel NPCM8XX peripherals are based on Poleg NPCM7XX.
This patchset was tested on the Arbel NPCM8XX evaluation board."
I'm leaving out the clk controller driver, which is still under
review.
* nuvoton/newsoc:
arm64: defconfig: Add Nuvoton NPCM family support
arm64: dts: nuvoton: Add initial NPCM845 EVB device tree
arm64: dts: nuvoton: Add initial NPCM8XX device tree
arm64: npcm: Add support for Nuvoton NPCM8XX BMC SoC
dt-bindings: arm: npcm: Add nuvoton,npcm845 GCR compatible string
dt-bindings: arm: npcm: Add nuvoton,npcm845 compatible string
dt-bindings: arm: npcm: Add maintainer
reset: npcm: Add NPCM8XX support
dt-bindings: reset: npcm: Add support for NPCM8XX
reset: npcm: using syscon instead of device data
ARM: dts: nuvoton: add reset syscon property
dt-bindings: reset: npcm: add GCR syscon property
dt-binding: clk: npcm845: Add binding for Nuvoton NPCM8XX Clock
dt-bindings: watchdog: npcm: Add npcm845 compatible string
dt-bindings: timer: npcm: Add npcm845 compatible string
|
|
Updated the NPCM reset driver to add support for Nuvoton BMC NPCM8XX SoC.
As part of adding NPCM8XX support:
- Add NPCM8XX specific compatible string.
- Add NPCM8XX USB reset.
- Add data to handle architecture-specific reset parameters.
- Some of the Reset Id and number of resets are different from NPCM7XX.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Using syscon device tree property instead of device data to handle the
NPCM general control registers.
In case the syscon not found the code still search for nuvoton,npcm750-gcr
to support DTS backward compatibility.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit b6b9585876da018bdde2d5f15d206a689c0d70f3.
This breaks MDIO on kswitch-d10, presumably because the global switch
reset is not released early enough anymore.
Reported-by: Michael Walle <michael@walle.cc>
Cc: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220713084010.168720-1-p.zabel@pengutronix.de
|
|
This driver can be built under COMPILE_TEST. Allow it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220711130624.1217599-1-p.zabel@pengutronix.de
|
|
If CONFIG_EXPERT is selected, allow selection of CONFIG_RESET_SIMPLE
if needed by the user.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220708165656.269507-1-ben.dooks@sifive.com
|
|
Add reset driver for Sunplus SP7021 SoC.
Signed-off-by: Qin Jian <qinjian@cqplus1.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Set RESET_MCHP_SPARX5 as a tristate and add MODULE_DEVICE_TABLE() to
allow building this driver as a module.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220617103730.490588-1-clement.leger@bootlin.com
|
|
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/drivers
TI Driver updates for v5.19
* wkup_m3: io isolation, voltage scaling, vtt regulator and a debug option to stop m3 in suspend.
* tisci: support for polled mode for system suspend, reset driver is now enabled for COMPILE_TEST
* knav, dma.. misc cleanups for IS_ERR, pm_run_time*, and various other fixups.
* tag 'ti-driver-soc-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
soc: ti: wkup_m3_ipc: Add debug option to halt m3 in suspend
soc: ti: wkup_m3_ipc: Add support for i2c voltage scaling
soc: ti: wkup_m3_ipc: Add support for IO Isolation
soc: ti: knav_qmss_queue: Use IS_ERR instead of IS_ERR_OR_NULL when checking knav_queue_open() result
soc: ti: pm33xx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
firmware: ti_sci: Switch transport to polled mode during system suspend
soc: ti: wkup_m3_ipc: Add support for toggling VTT regulator
soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: knav_dma: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
reset: ti-sci: Allow building under COMPILE_TEST
soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
soc: ti: omap_prm: Use of_device_get_match_data()
soc: ti: pruss: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: replace usage of found with dedicated list iterator variable
soc: ti: wkup_m3_ipc: fix platform_get_irq.cocci warning
Link: https://lore.kernel.org/r/20220507163424.pvqnwrxpoo73lmp2@debtless
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm/drivers
Reset controller updates for v5.19
Add Meson-S4 SoC reset controller support to reset-meson, AST2600 LPC
reset controller support to reset-simple, and R9A07G054 USBPHY reset
controller support to reset-rzg2l-usbphy-ctrl. Add ACPI _RST support to
device_reset(), simplify the uniphier-glue reset driver using bulk API
and devres and clean up its dt-bindings docs. Convert most dt-bindings
docs from txt to yaml.
* tag 'reset-for-v5.19' of git://git.pengutronix.de/pza/linux:
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
dt-bindings: reset: nuvoton,npcm-reset: Convert to yaml
dt-bindings: reset: lantiq,reset: Convert to yaml
dt-bindings: reset: bitmain,bm1880-reset: Convert to yaml
dt-bindings: reset: berlin: Convert to yaml
dt-bindings: reset: ath79: Convert to yaml
dt-bindings: reset: amlogic,meson-axg-audio-arb: Convert to yaml
dt-bindings: reset: uniphier-glue: Clean up clocks, resets, and their names using compatible string
reset: Kconfig: Make RESET_RZG2L_USBPHY_CTRL depend on ARCH_RZG2L
reset: ACPI reset support
reset: simple: Add AST2600 compatible
reset: reset-meson: add support for the Meson-S4 SoC Reset Controller
dt-bindings: reset: add bindings for the Meson-S4 SoC Reset Controller
dt-bindings: reset: Add compatible for Meson-S4 Reset Controller
reset: uniphier-glue: Use devm_add_action_or_reset()
reset: uniphier-glue: Use reset_control_bulk API
Link: https://lore.kernel.org/r/20220503160057.46625-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The USBPHY Control block is identical on Renesas RZ/G2L and RZ/V2L SoC's,
so instead of adding dependency for each SoC's add dependency on
ARCH_RZG2L. The ARCH_RZG2L config option is already selected by
ARCH_R9A07G044 and ARCH_R9A07G054.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220406071647.14037-1-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
Some of the IO devices like I2C or SPI require reset at runtime to
recover from an error condition without changing the power state of
the system. Added check for ACPI handle and a call to method '__RST'
if supported. Devices using device tree method are unaffected by this.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
[p.zabel@pengutronix.de: wrap in #ifdef CONFIG_ACPI due to missing stubs]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220307135626.16673-1-kyarlagadda@nvidia.com
|
|
Similar to the 2400 and 2500, the LPC controller has some simple reset
lines that are used by the UART devices.
This is already documented in LPC bindings document.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220221072650.129348-1-joel@jms.id.au
|
|
Compared to the A1 SoCs the number of RESET registers is different
and the offset for the level registers is the same. Add a new
compatible string and struct meson_reset_param to add support for the
reset controller on the S4 SoC.
Signed-off-by: Zelong Dong <zelong.dong@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220107023931.13251-4-zelong.dong@amlogic.com
|
|
Slightly simplify uniphier_glue_reset_probe() and drop
uniphier_glue_reset_remove() by using devm_add_action_or_reset()
for clock and reset cleanup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20211215093829.3209416-2-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This driver already uses the clk_bulk API. Simplify the driver by using
the reset_control_bulk API as well.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20211215093829.3209416-1-p.zabel@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Since commit 043cfff99a18 ("firmware: ti_sci: Fix compilation failure
when CONFIG_TI_SCI_PROTOCOL is not defined") it is possible to build
reset-ti-sci under CONFIG_COMPILE_TEST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220404094500.2708816-1-p.zabel@pengutronix.de
|
|
This reverts following commit 69125b4b9440 ("reset: tegra-bpmp: Revert
Handle errors in BPMP response").
The Tegra194 HDA reset failure is fixed by commit d278dc9151a0 ("ALSA:
hda/tegra: Fix Tegra194 HDA reset failure"). The temporary revert of
original commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") can be removed now.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/1641995806-15245-1-git-send-email-spujar@nvidia.com
|
|
Deasserting the reset is vital, therefore bail out in case of error.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/b2131908-0110-006b-862f-080517f3e2d8@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Delta TN48M CPLD exposes resets for the following:
* 88F7040 SoC
* 88F6820 SoC
* 98DX3265 switch MAC-s
* 88E1680 PHY-s
* 88E1512 PHY
* PoE PSE controller
Controller supports only self clearing resets.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20220131133049.77780-5-robert.marko@sartura.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull RISC-V SoC updates from Arnd Bergmann:
"Add support for StarFive JH7100 RISC-V SoC
This adds support for the StarFive JH7100, including the necessary
device drivers and DT files for the BeagleV Starlight prototype board,
with additional boards to be added later. This SoC promises to be the
first usable low-cost platform for RISC-V.
I've taken this through the SoC tree in the anticipation of adding a
few other Arm based SoCs as well, but those did not pass the review in
time, so it's only this one"
* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
reset: starfive-jh7100: Fix 32bit compilation
RISC-V: Add BeagleV Starlight Beta device tree
RISC-V: Add initial StarFive JH7100 device tree
serial: 8250_dw: Add StarFive JH7100 quirk
dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
pinctrl: starfive: Add pinctrl driver for StarFive SoCs
dt-bindings: pinctrl: Add StarFive JH7100 bindings
dt-bindings: pinctrl: Add StarFive pinctrl definitions
reset: starfive-jh7100: Add StarFive JH7100 reset driver
dt-bindings: reset: Add Starfive JH7100 reset bindings
dt-bindings: reset: Add StarFive JH7100 reset definitions
clk: starfive: Add JH7100 clock generator driver
dt-bindings: clock: starfive: Add JH7100 bindings
dt-bindings: clock: starfive: Add JH7100 clock definitions
dt-bindings: interrupt-controller: Add StarFive JH7100 plic
dt-bindings: timer: Add StarFive JH7100 clint
RISC-V: Add StarFive SoC Kconfig option
|
|
We need to include linux/io-64-nonatomic-lo-hi.h or readq/writeq won't
be defined when compiling on 32bit architectures:
On i386:
../drivers/reset/reset-starfive-jh7100.c: In function ‘jh7100_reset_update’:
../drivers/reset/reset-starfive-jh7100.c:81:10: error: implicit declaration of function ‘readq’; did you mean ‘readl’? [-Werror=implicit-function-declaration]
value = readq(reg_assert);
^~~~~
../drivers/reset/reset-starfive-jh7100.c:86:2: error: implicit declaration of function ‘writeq’; did you mean ‘writel’? [-Werror=implicit-function-declaration]
writeq(value, reg_assert);
^~~~~~
On m68k:
drivers/reset/reset-starfive-jh7100.c:81:17: error: implicit declaration of function 'readq'; did you mean 'readb'? [-Werror=implicit-function-declaration]
drivers/reset/reset-starfive-jh7100.c:86:9: error: implicit declaration of function 'writeq'; did you mean 'writel'? [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[3]: *** [scripts/Makefile.build:289: drivers/reset/reset-starfive-jh7100.o] Error 1
make[2]: *** [scripts/Makefile.build:572: drivers/reset] Error 2
make[1]: *** [Makefile:1969: drivers] Error 2
make: *** [Makefile:226: __sub-make] Error 2
Fixes: 0be3a1595bf8 ("reset: starfive-jh7100: Add StarFive JH7100 reset driver")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20211220121800.760846-1-kernel@esmil.dk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add a driver for the StarFive JH7100 reset controller.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
|
|
If pm_runtime_resume_and_get() fails then it returns w/o the RPM usage
counter being incremented. In this case call pm_runtime_put() in
remove() will result in a usage counter imbalance. Therefore check the
return code of pm_runtime_resume_and_get() and bail out in case of error.
Fixes: bee08559701f ("reset: renesas: Add RZ/G2L usbphy control driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/ec24e13f-0530-b091-7a08-864577b9b3be@gmail.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") fixed an issue in the Tegra BPMP error handling but has
exposed an issue in the Tegra194 HDA driver and now resetting the
Tegra194 HDA controller is failing. For now revert the commit
c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP response")
while a fix for the Tegra HDA driver is created.
Fixes: c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP response")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211112112712.21587-1-jonathanh@nvidia.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
|
|
This patch extends sparx5 driver to support also the lan966x. The
process to reset the switch is the same only it has different offsets.
Therefore make the driver more generic and add support for lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211018091522.1113510-3-horatiu.vultur@microchip.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
